(407) 281-9000
Mon - Fri 7:30 A.M. - 5 P.M.

0 $0.00
items in your cartto quote Checkout
Ooops no items were found.
Try something else.
Ok
Loading…
To cart
Quote Me
Checkout
0
Ergodyne

Slips hand tool attachment trap

Category Accessories
19744
Ergodyne

Slips hand tool attachment trap

Item Code: 19744
Category Accessories

Description

Perfect retrofit tool attachments for small hand tools to help reduce the risk of dropped objects and increase workplace safety. Connection points for tool lanyards can be tricky to find, especially on smaller hand tools like screw drivers and hex keys (Allen wrenches). No additional install tools, wrapping or shrinking needed. Simple installation - slip the tool attachment on to the tool and connect a Squids® Tool Lanyard to complete your tethering system. Puncture the interior membrane of the Tool Slip and slide the attachment to the desired location. The star points of the attachment’s interior will hold its location and the swiveling exterior ring will provide a connection point for tool lanyards. Unlike competitors that offer a fitted cap that can cover up information (ex: the end of a screwdriver) these solutions leave the end open. Single piece design is easier to install compared to competitors that require two to three pieces to be assembled onto the tool. Perfect for small hand tools that are challenging to connect to tool lanyards. Screw drivers, small combination wrenches, punches, hex (Allen) wrenches and the like do not have captive connection points, and the low-profile designs can make it difficult for tapes, shrinks and tails to be applied. Tether tools up to 1 lb. based on their diameter. Four sizes of Slips are compatible on tools with diameters ranging from 0.05" (1.3 mm) to 1/2" (12.5 mm). Check out the size chart for specific ranges per size.
While working at-heights, it is important to tether tools as part of your overall fall protection plan, but the lack of these connection points can make that difficult.

Features:
• Approved to the ANSI/ISEA 121-2018 standard
• Patent-pending one-piece design easily slides onto small hand tools without requiring additional tools to install or complicated wrapping or shrinking to apply
• Swiveling exterior ring spins 360° allowing screwdrivers and other rotating tools to be used without issue
• ABS outer ring provides strength and durability in all environments, testing in hot, cold and wet conditions
• Flexible inner core grips tool after application securing it as an attachment pointfor a tool lanyard preventing dropped objects
• Available in four sizes compatible with tools ranging from 0.05†(1.3 mm) to1/2†(12.5 mm)
• Maximum tethering capacity up to 1 lb. (0.45 kg) dependent on size (review size chart for capacity information)
• Intended for singled use, discard after after removal and replace
• PATENTED DESIGN

Specifications

Color

White

Plant Maintenance Types

Adhesive Tape/Treads

Sizes

12 mm x 55 m

- +
Add to quicklist
Compare
Ergodyne

Slips hand tool attachment trap

Category Accessories
19744
Ergodyne

Slips hand tool attachment trap

Item Code: 19744
Category Accessories

Description

Perfect retrofit tool attachments for small hand tools to help reduce the risk of dropped objects and increase workplace safety. Connection points for tool lanyards can be tricky to find, especially on smaller hand tools like screw drivers and hex keys (Allen wrenches). No additional install tools, wrapping or shrinking needed. Simple installation - slip the tool attachment on to the tool and connect a Squids® Tool Lanyard to complete your tethering system. Puncture the interior membrane of the Tool Slip and slide the attachment to the desired location. The star points of the attachment’s interior will hold its location and the swiveling exterior ring will provide a connection point for tool lanyards. Unlike competitors that offer a fitted cap that can cover up information (ex: the end of a screwdriver) these solutions leave the end open. Single piece design is easier to install compared to competitors that require two to three pieces to be assembled onto the tool. Perfect for small hand tools that are challenging to connect to tool lanyards. Screw drivers, small combination wrenches, punches, hex (Allen) wrenches and the like do not have captive connection points, and the low-profile designs can make it difficult for tapes, shrinks and tails to be applied. Tether tools up to 1 lb. based on their diameter. Four sizes of Slips are compatible on tools with diameters ranging from 0.05" (1.3 mm) to 1/2" (12.5 mm). Check out the size chart for specific ranges per size.
While working at-heights, it is important to tether tools as part of your overall fall protection plan, but the lack of these connection points can make that difficult.

Features:
• Approved to the ANSI/ISEA 121-2018 standard
• Patent-pending one-piece design easily slides onto small hand tools without requiring additional tools to install or complicated wrapping or shrinking to apply
• Swiveling exterior ring spins 360° allowing screwdrivers and other rotating tools to be used without issue
• ABS outer ring provides strength and durability in all environments, testing in hot, cold and wet conditions
• Flexible inner core grips tool after application securing it as an attachment pointfor a tool lanyard preventing dropped objects
• Available in four sizes compatible with tools ranging from 0.05†(1.3 mm) to1/2†(12.5 mm)
• Maximum tethering capacity up to 1 lb. (0.45 kg) dependent on size (review size chart for capacity information)
• Intended for singled use, discard after after removal and replace
• PATENTED DESIGN

Specifications

Color

White

Plant Maintenance Types

Adhesive Tape/Treads

Sizes

12 mm x 55 m

- +
Add to quicklist
Compare
SEARCH ×